This message is marked as Important.

Subject: HOW TO - Differential Fluid Change w/Pics Author: shogun (moderator) : member since March, 2004 : 16310 posts Posted on: 2009-08-11 08:27:02

This How To was performed on a 1995 BMW 540i that was produced in the month of September. There could be slight variations between models and years as there were different Differentials available across production of the 5 series if memory serves me correctly, but overall this should be a basic outline.
__________________________________________________ ______________
NOTICE: I do not take responsibility for your safety nor potential damage you incur upon your vehicle. I provide this information with the intent of providing free information on how to perform this automotive service. This is not guaranteed to be the best means of performing this work and you should express extreme caution while underneath a vehicle as well as exposing yourself to HAZARDOUS automotive fluids. Wear safety glasses, use rubber gloves, dispose of used fluids in an environmentally safe fashion and support your car on a level surface with the proper equipment.
__________________________________________________ ______________

Materials Needed List:

1) Bucket or Oil Drain pan.
2) 14mm Allen Key - I found this in a 3 piece kit at Autozone. It included 12mm/14mm/17mm Allens already in sockets that you'll need to remove. You'll have to cut your 14mm in half to fit it. I couldn't not find this in any other locations (Tried Sears, Pepboy's, Autobarn, Home Depot)
3) 3/8 Drive Socket w/14mm Socket (shortest possible) and/or 14mm Wrench.
4) 2 quarts or 1.9liters as specified in Bentley manual.
5) Differential Fluid, available at Pepboys. You'll need 2-3 Bottles of fluid. I used Mobil 75w90 Oil.
6) 6 foot rubber hose, small enough to fit within the differential fill hole.
7) Penetrating Oil is a god send, use it. When something like this hasn't been opened since it was built, it kinda stays budged.

Note:
The Bentley Manual specifies the following
525i and 530i ..................... 1.7 Liters (1.8 qt)
535i and 540i ...................... 1.9 Liters (2.0 qt)

Prep -
1) Drive the car a few miles to warm up the fluid for easier draining
2) Get the car jacked up on jack stands, all four sides to allow for level surface.
3) Using a grinder, cut your 14mm Allen into 2 pieces, one slightly longer than the other.. That way, one can be used for the socket and the other can be used for a wrench. If you are buying the 3pc kit from Autozone, you'll need to put the allen with its socket into a vice grip. Taking a hammer and using a chisel or flat head screw driver, knock the socket until the Allen falls out. Now your ready to cut it.

Fill Area
This a picture of the Fill area, you should make sure you loosen this plug first otherwise, you'll have a nicely drained diff and no way to fill it.

Photograph #1

Drain Area
This is your drain area, after loosening the Fill plug, now you can proceed to loosen the drain plug. Have your gloves on and your bucket ready.

Photograph #2

Shot of Drain Plug being loosened:
Notice the minimal distance between the back of the ratchet and the plate? This is one of the reasons you cut the Allen. It just won't fit in there on a socket without cutting first. Once again, same for the fill plug.

Photograph #3

Near Success: Fluid being led to its disposal by gravity
Not too pretty is it? Thats a 125,000 Miles on what was likely the same fluid from day 1 of this car's life. Notice how thick and unclear the fluid is. Nasty.

Photograph #4


Not Photographed but not forgotten:
Now your differential is bone dry and ready to be filled. Replace the drain plug back in place nice and snug.

At this point its useful to have a second person. Using the 6 foot rubber hose, insert one end into the differential at the Fill area in Photograph #1.
(The second person is there to hold the hose in the fill hole as well as let you know when your overfill point is reached) Place the tip of the gear lube fluid bottle into the hose and stand up from under the car. Your now facing your trunk and holding the bottle with the hose attached.

With the bottle inserted into the tube and now upside down, take a knife (or wire cutters ) and pierce a large hole in the bottom of the bottle to allow gravity to once again make short work of the fill process. Your lube should be traveling successfully into the differential and your nearly done. Keep filling until some oil starts to spill out of the fill area. Remove the hose and replace the fill plug, tightly. Make sure your drain plug is tightly in place while your there as well. Don't forget to clean up any spilled oil.

Your done!

You can now drive your car, don't forget to check in a few days if there are any leaks now and a few days later, this is why its important to clean the oil off the parts when you finish initially.
Hope this helps some folks out. If I missed anything important, please post it and I'll add it to the post.

wirte up and pics by Vile, posted on 06-03-2007
original post:
http://forums.bimmerforums.com/forum/showthread.php?t=762375

E32 750iL 11/88, E32 750iL Highline 03/90
SHOGUN'S TRICKS AND TIPS FOR THE SEVEN SERIES

• HOW TO - Differential Fluid Change w/Pics (pic) - shogun 2009-08-11 08:27:02 (1795 views)
  • This is a great writeup. I used it a couple of weeks ago to change my LSD oil... - eaglecomm 2009-08-12 11:01:28 (292 views)