Subject: Above install insctuctions for CPT3000/4000, below are for CPT5000/6000/7000/800 Author: ambishop as Martin : member since December, 2003 : 3198 posts Posted on: 2005-10-27 20:04:31

Parts Information

1) BMW Bluetooth Eject Box - Holds snap in connectors

2) BMW Bluetooth Antenna - Provides short range communication (approx 30 ft) to Bluetooth cellular phone

3) FAKRA to FAKRA Antenna Jumper - Connects the Bluetooth antenna to the BMW ULF Bluetooth Module

4) FAKRA to Mini UHF Antenna Jumper - Connects the BMW Eject Box to center console RF BMW prewiring

5) FAKRA to Mini UHF Antenna Jumper - Connects the BMW RF prewiring in the trunk area too either BMW dual band compensator or BMW dual band antenna

6) BMW Bluetooth ULF Module - Mounts in the location of BMW TCU unit and connects to BMW cellular phone prewiring. One wire connects to x400 plug and the other to the car's DB25 plug





PROCEDURE



To Install and Connect the BMW Bluetooth Hands-Free System

Disconnect Battery Prior to starting installation

Remove Bluetooth PassKey Sticker on Side of BMW Bluetooth ULF Module. Store in a accessible location for later phone pairing

Verify that you have a mic preinstalled in your vehicle (If you have phone now, you have the mic) - remove center console light, and overhead cover. Verify microphone is present, if not you will need to purchase a Microphone





Remove the Vehicle's TCU (Telephone Control Unit) - If equipped

Follow standard procedures on Removing navigation computer. TIS 65 90 510 See www.e38.org for procedure

Follow standard procedures on Removing Telephone Transceiver. TIS 84 11 520 See www.e38.org for procedure



Replace the Vehicle's TCU with Bluetooth ULF Module - Secure to vehicle with existing bracket, or wire ties

Connect DB25 connector from ULF module to DB25 connector in vehicle.



Find a suitable location for the BMW Bluetooth Antenna within the cabin of the vehicle - C-pillar is an easy installation in the E38.

Follow standard procedures on Removing C-pillar. TIS 51 43 251 See www.e38.org for procedure

Once drivers side C-pillar cover is off, route FAKRA to FAKRA Antenna Jumper from rear compartment to C-pillar and mount with double sided tape.



Remove the Vehicle's rear Fresh Air Grill - Just below and to the rear of front arm rest

Follow standard procedures on Removing and installing/replacing fresh-air grill in rear of car. TIS 64 22 190 See www.e38.org for procedure



Remove the Vehicle's telephone Eject Box - In the center arm rest: Slide arm rest forward lift up on cover (not necessary but optional to unscrew 2 phillips head screws and remove arm rest from vehicle)

Follow standard procedures on Removing and installing/replacing Eject Box. TIS 84 11 510 See www.e38.org for procedure



Replace the Vehicle's telephone Eject Box with BMW Bluetooth Eject Box- Remove the 4 T20 TORX screws holding down vehicle eject kit. Replace with Bluetooth Eject Kit and route Bluetooth wiring thru holes provided. Connect 18 Pin ELO connector and FAKRA to mini UHF adapter the adapter harness.



Reassemble Vehicle and Reconnect battery.



Pairing Procedure

The pairing procedure that must be initiated through the phone will differ corresponding to the different menu configurations of the various Bluetooth mobile phones on the market. The user’s manual of the phone should always be referenced for specific steps on how to activate the Bluetooth feature and to pair/link devices.
The following steps are generalized steps that should help in activating the Bluetooth function of most phones:
IN VEHICLE:
1. Depress the pairing button for at least 1 second prior to switching on the ignition and continue to hold the button down for
approximately 2-3 seconds after the ignition is turned on.
2. Release the button.

ON PHONE:
1. Locate the connection/settings menu and select Bluetooth
2. Select the response that will activate the Bluetooth feature of the phone.
3. Next select a menu option that will allow you to “Discover” or “Search” for active Bluetooth devices.
4. If the phone identifies/finds a device select it and follow the indicated steps to complete the pairing process which will include the request for the Bluetooth passkey. The Bluetooth passkey is the sticker you removed previously and is also on the ULF module parts label.
5. Once the phone is successfully paired to the device cycle the ignition switch off and back on and the devices should wirelessly connect within 30 seconds. When the connection is established the phone will display a connection symbol.


 

• Build your own Bluetooth Retrofit Kit - Martin 2005-10-27 19:32:40 (4107 views)
  • I installed the euro armrest and removed the phone - kepdan 2005-11-17 23:45:01 (408 views)
    • yes, but you need a pairing button when you want to add phones (nt) - Martin 2005-11-19 14:31:10 (352 views)
      • Cool... what is that? (nt) - kepdan 2005-11-19 14:43:39 (341 views)
  • update--- sorry for the typos but please note changes - Martin 2005-11-17 12:05:56 (518 views)
  • Re: Build your own Bluetooth Retrofit Kit - dahr 2005-11-13 00:04:30 (340 views)
  • SENT YOU AN E-MAIL AMB - alev8 2005-10-29 15:47:09 (318 views)
    • Re: SENT YOU AN E-MAIL AMB - jamvonco 2005-11-18 02:49:50 (305 views)
  • Re: Build your own Bluetooth Retrofit Kit - rampage 2005-10-28 13:29:17 (413 views)
    • Re: Build your own Bluetooth Retrofit Kit - zaktora 2005-11-19 04:45:34 (309 views)
  • Re: Build your own Bluetooth Retrofit Kit (pic) - farnarkler 2005-10-28 07:51:32 (829 views)
    • You would need to get a wiring diagram for that phone - Martin 2005-10-28 22:48:03 (449 views)
  • Above install insctuctions for CPT3000/4000, below are for CPT5000/6000/7000/800 - Martin 2005-10-27 20:04:31 (705 views)
  • Bluetooth Bracket Part numbers - Martin 2005-10-27 19:50:46 (574 views)
    • Re: Bluetooth Bracket Part numbers - rdemere 2005-10-29 14:19:19 (439 views)