This message is marked as Important.

Subject: Build your own Bluetooth Retrofit Kit Author: ambishop as Martin (Sponsoring Vendor) : member since December, 2003 : 3192 posts Posted on: 2005-10-27 19:32:40

If you have a BMW E38, or E39 and want to do an install below are the parts needed.

Db25 to ULF 54 pin connector adapter - Custom made. I have 10 left $100 Each plus $10 shipping send to martin@bimmernav.com via paypal first come first served. THEY ARE DIFFERENT FOR CPT5000/6000 & CPT7000/8000. CPT5000/6000 $10 additional charge.

I also have 5 fakra to fakra jumpers and about FAKRA to Mini-Uhf adapter. If you buy the DB25-ULF 54 adapter you can have them at the below dealer prices. I also have one Mic. still in the box from the dealer. Version 319 (typical for 2001 E38, but works for all)

Parts needed CPT5000-CPT8000 Kits
84 32 0 027 140 FAKRA to Mini-Uhf adapter $9.39
61 12 0 137 616 FAKRA to FAKRA Jumper $16.71
84 50 6 928 461 Bluetooth ANTENNA $14.40
84 21 6 933 415 Eject Kit $75.00
BMW ULF module. Any ULF module will work. Dealer only part

Optional
84 31 6 938 762 New Style MIC
84 11 0 027 942 SES Owners Manual
84 11 0 302 638 ULF Owners Manual
84 11 0 302 646 ULF Passkey
84 11 0 025 711 FALKRA TO MINI U 1 $6.75 For connecting to compensator and antenna (only should be needed if you do not have an antenna)

You MUST get an Eject kit and slightly modify the wires
CPT7000 - 8000
ELO18 wires need to be as follows (need to move Brown and Red)
Green 1
Brown 17 (move 2 to 17)
Red 10 (move 5 to 10)
White 18
Jumper 6 & 9

CPT5000 – 6000
ELO18 wires need to be as follows (need to move Brown and Red)
ELO18 MOVE wires
Green 13
Brown 17 (move 2 to 17)
Red 8 (move 5 to 8)
White 18
Jumper 6 &9
Jumper 11 & 14

****CPT3000-4000
FULL BMW E39 Bluetooth harness, must be modified $135 dealer, and about 1 hour of work. Or do the full install and spend about 4 hours in the car.
84 32 0 027 140 FAKRA to Mini-Uhf adapter $9.39
61 12 0 137 616 FAKRA to FAKRA Jumper $16.71
84 50 6 928 461 Bluetooth ANTENNA 1 $14.40
84 21 6 933 415 Eject Kit
BMW ULF module. Any ULF module will work. Dealer only part


Install instructions found on the web or some good info below

Parts Information

1) BMW Bluetooth Eject Box - Holds snap in connectors

2) BMW Bluetooth Antenna - Provides short range communication (approx 30 ft) to Bluetooth cellular phone

3) FAKRA to FAKRA Antenna Jumper - Connects the Bluetooth antenna to the BMW ULF Bluetooth Module

4) FAKRA to Mini UHF Antenna Jumper - Connects the BMW Eject Box to center console RF BMW prewiring

5) FAKRA to Mini UHF Antenna Jumper - Connects the BMW RF prewiring in the trunk area too either BMW dual band compensator or BMW dual band antenna

6) BMW Bluetooth ULF Module - Mounts in the location of BMW TCU unit and connects to BMW cellular phone prewiring. One wire connects to x400 plug and the other to the car's DB25 plug





PROCEDURE



To Install and Connect the BMW Bluetooth Hands-Free System

Disconnect Battery Prior to starting installation

Remove Bluetooth PassKey Sticker on Side of BMW Bluetooth ULF Module. Store in a accessible location for later phone pairing

Verify that you have an Telephone antenna preinstalled in your vehicle (If you have phone now, you have the mic) - remove center console light, and overhead cover. Verify microphone is present, if not you will need to purchase a Microphone





Remove the Vehicle's TCU (Telephone Control Unit) - If equipped

Follow standard procedures on Removing navigation computer. TIS 65 90 510 See www.e38.org for procedure

Follow standard procedures on Removing Telephone Transceiver. TIS 84 11 520 See www.e38.org for procedure



Replace the Vehicle's TCU with Bluetooth ULF Module - Secure to vehicle with existing bracket, or wire ties

Remove Car's x400 plug located at the rear of the vehicle on near the inside of the tail lights. Connect DB25 connector from ULF module to DB25 connector in vehicle, and connect the NEW x400 plug to the vehicle.



Replace the Vehicle's DB25 microphone plug with the WHITE plug from the Bluetooth harness. The microphone plug is located in the trunk area right next to the TCU location. It is a three pin connector with a silver label that says KS or similar. ! IMPORTANT ! ONLY use the white microphone connector on the bluetooth harness! The bluetooth harness also has a black plug for the optional RF compensator (booster) that could also fit although it should be taped down to the harness to prevent accidental connection. The correct White microphone plug on the Bluetooth harness has a yellow and two black wires.



Find a suitable location for the BMW Bluetooth Antenna within the cabin of the vehicle - C-pillar is an easy installation in the E38.

Follow standard procedures on Removing C-pillar. TIS 51 43 251 See www.e38.org for procedure

Once drivers side C-pillar cover is off, route FAKRA to FAKRA Antenna Jumper from rear compartment to C-pillar and mount with provided double sided tape.



Remove the Vehicle's rear Fresh Air Grill - Just below and to the rear of front arm rest

Follow standard procedures on Removing and installing/replacing fresh-air grill in rear of car. TIS 64 22 190 See www.e38.org for procedure



Remove the Vehicle's telephone Eject Box - In the center arm rest: Slide arm rest forward lift up on cover (not necessary but optional to unscrew 2 phillips head screws and remove arm rest from vehicle)

Follow standard procedures on Removing and installing/replacing Eject Box. TIS 84 11 510 See www.e38.org for procedure



Replace the Vehicle's telephone Eject Box with BMW Bluetooth Eject Box- Remove the 4 T20 TORX screws holding down vehicle eject kit. Replace with Bluetooth Eject Kit and route Bluetooth wiring thru holes provided. Connect 18 Pin ELO connector and FAKRA to mini UHF adapter the adapter harness.



Reassemble Vehicle and Reconnect battery.



Pairing Procedure

The pairing procedure that must be initiated through the phone will differ corresponding to the different menu configurations of the various Bluetooth mobile phones on the market. The user’s manual of the phone should always be referenced for specific steps on how to activate the Bluetooth feature and to pair/link devices.
The following steps are generalized steps that should help in activating the Bluetooth function of most phones:
IN VEHICLE:
1. Depress the pairing button for at least 1 second prior to switching on the ignition and continue to hold the button down for
approximately 2-3 seconds after the ignition is turned on.
2. Release the button.

ON PHONE:
1. Locate the connection/settings menu and select Bluetooth
2. Select the response that will activate the Bluetooth feature of the phone.
3. Next select a menu option that will allow you to “Discover” or “Search” for active Bluetooth devices.
4. If the phone identifies/finds a device select it and follow the indicated steps to complete the pairing process which will include the request for the Bluetooth passkey. The Bluetooth passkey is the sticker you removed previously and is also on the ULF module parts label.
5. Once the phone is successfully paired to the device cycle the ignition switch off and back on and the devices should wirelessly connect within 30 seconds. When the connection is established the phone will display a connection symbol.


 

• Build your own Bluetooth Retrofit Kit - Martin 2005-10-27 19:32:40 (3524 views)
  • I installed the euro armrest and removed the phone - kepdan 2005-11-17 23:45:01 (367 views)
    • yes, but you need a pairing button when you want to add phones (nt) - Martin 2005-11-19 14:31:10 (322 views)
      • Cool... what is that? (nt) - kepdan 2005-11-19 14:43:39 (318 views)
  • update--- sorry for the typos but please note changes - Martin 2005-11-17 12:05:56 (484 views)
  • Re: Build your own Bluetooth Retrofit Kit - dahr 2005-11-13 00:04:30 (311 views)
  • SENT YOU AN E-MAIL AMB - alev8 2005-10-29 15:47:09 (290 views)
    • Re: SENT YOU AN E-MAIL AMB - jamvonco 2005-11-18 02:49:50 (280 views)
  • Re: Build your own Bluetooth Retrofit Kit - rampage 2005-10-28 13:29:17 (398 views)
    • Re: Build your own Bluetooth Retrofit Kit - zaktora 2005-11-19 04:45:34 (282 views)
  • Re: Build your own Bluetooth Retrofit Kit (pic) - farnarkler 2005-10-28 07:51:32 (774 views)
    • You would need to get a wiring diagram for that phone - Martin 2005-10-28 22:48:03 (425 views)
  • Above install insctuctions for CPT3000/4000, below are for CPT5000/6000/7000/800 - Martin 2005-10-27 20:04:31 (663 views)
  • Bluetooth Bracket Part numbers - Martin 2005-10-27 19:50:46 (540 views)
    • Re: Bluetooth Bracket Part numbers - rdemere 2005-10-29 14:19:19 (419 views)